Scott's Gunsmithing Service
Scott's Gunsmithing Service

AR15 Reliability Services

 

 



*Cut M4 Feed Ramps & Polish Feed Ramps and Barrel Extension Lug Recesses $75.00-$150.00 Labor
NOTE: The Barrel MUST be removed from the Upper receiver for this Service to be performed. The Price varies depending on the difficulty removing the Barrel and.or Rail Assembly on the Upper.

 

 

 

*Polish Feed Ramps & Barrel Extension Lug Recesses $50.00-$125.00 Labor
NOTE: The Barrel MUST be removed from the Upper receiver for this Service to be performed. The Price varies depending on the difficulty removing the Barrel and/or Rail Assembly on the Upper.

 

Ramp Job & Re-Cut Services primarily help with reliability with wide ranges of Ammunition and certain Projectiles such as Soft Point, Ballistic Tip, and Hollow Point. Often AR15's have Feed Ramps that are rough, or worse are "Clickers". A "Clicker" Ramp can be identified with a Ballpoint Pen. You run the Pen tip up the where the Upper Receiver Stops and the Barrel Extension Ramps Begin. If the Tip hangs up you have a "Clicker". This usually results in a Failure to Feed Malfunctions with certain Ammunition. A "Clicker" can also force a Projectile to be forced into the Casing which can increase Chamber Pressure dramatically, which is far from ideal.

This Service also keeps the Locking Lug Area and your entire Weapon from accumulating Brass Shavings which can affect reliability. Polishing the Feed Ramps minimizes rough areas that shave material as Ammunition pass over them. If enough Brass/Copper Shavings accumulate the Bolt will fail to rotate into battery and will result in malfunctions. Alternate Benefits include reducing Brass Casing Damage. Reloaders tend to appreciate this added benefit. Effortless Feeding and Proper Ramp Geometry also minimizes Bullet Deflection when Feeding & Chambering Rounds. Projectile Deflection and Damage can affect the Weapons Accuracy & Consistency.

 

This Service allows the Weapon to cycle easier when Clean or Fouled, allows eased Chambering, decreases Brass Casing Rim Damage.

 

 

 

*Tune Extractor and Ejector System $50.00 Labor (Extractor NOT INCLUDED)
NOTE: Includes
New CS Ejector Spring
New CS Extractor Spring
New Extractor Insert and O-Ring
Contour and Polish the Ejector
De-Burr Ejector hole. This prevents Ejector binding when fouled and/or hot.
Contour and Polish the Extractor contact surfaces. This eases Round Chambering, and minimizes Casing Rim Damage for easier Reloading of the Brass

 

 

 

*Polish Bolt Group Assembly $65.00 Labor
NOTE: I can NOT perform this Service on a Un-Shrouded Bolt Carriers, Nickle Boron Treated Parts, Hard Chromed Parts, or Notched Hammers. If you have a Notched Hammer we can install a Milspec Rounded Hammer for $25.00. If you have an Un-Shrouded Bolt Carrier we can provide a M16 Carrier for $95.00
NOTE: Includes
We De-Burr Firing Pin Hole
Check for Binding with the Firing Pin
Polish Hammer Face
Check for Free-Float between the Firing Pin and Cam Pin
Contour and Polish the Extractor contact surfaces
Polish underside of the BOTTOM 3 Bolt Head Locking Lugs. This keeps the 3 Lower Lugs from Gouging and Scraping the Rounds in your Magazine when fired or hand cycled, thus a cleaner smoother Weapon System
Polish tail of Bolt Carrier. This eliminates Receiver Extension damage and Buffer Damage
Polish Buffer Spring ends. This prevents Buffer Tube Friction/Galling
Polish underside of Bolt Carrier. This reduces Hammer/Carrier Drag and reduces Short Stroking probability when lube is thin/absent or when heavy fouling occurs

 

We Polish and Contour the Extractor. The Polished Extractor Face eases Round Chambering, and minimizes Casing Rim Damage. The De-Burred Firing Pin Hole decreases the likelihood of Misfeed Malfunctions.

 

 

 

*Carrier Polish, Ramp Job, with Extractor/Ejector Tuning PACKAGE $200.00 Labor

All of the above Modifications lead to a CLEANER and more reliable AR15. The Polished areas are NOT prone to rust, the polished surface seals the metal extremely well and Metal Heat Treat/Hardness is NOT affected.

 

 

 

*Clean and Tune Gas System $75.00 Labor (Parts Not Included)
Includes:

Clean Gas Tube or replace if necessary

Check Gas Block/FSB Alignment

Remove Front Sight Base/Gas Block and clean

Check Gas Port

Clean Barrel Chamber and Barrel Extension

Check Gas Rings and replace if necessary

Re-Install Front Sight Base

Dis-Assemble Bolt Carrier and clean carbon from Bolt Tail

Clean Gas Key or replace if necessary

Re-Install Gas Key Bolts or replace if necessary and seal with Loctite seal

Re-Torque Gas Key Screws, and Re-Stake

 

 

 

*Carrier Polish, Ramp Job, with Extractor/Ejector Tuning, Gas System Tuning PACKAGE $250.00 Labor

All of the above Modifications lead to a CLEANER and more reliable AR15. The Polished areas are NOT prone to rust, the polished surface seals the metal extremely well and Metal Heat Treat/Hardness is NOT affected.



Contact Us

Scott's Gunsmithing Service

231 Thelma Avenue

Glen Burnie, MD 21061

Phone: 410 761-9815

Fax: 410-761-9816



 

You can also or use our contact form.

Business Hours

Sunday        CLOSED

Monday       CLOSED

Tuesday      10:00 A.M.-6:00 P.M.

Wednesday 10:00 A.M.-6:00 P.M.

Thursday     10:00 A.M.-6:00 P.M.

Friday          10:00 A.M.-6:00 P.M.

Saturday       9:00 A.M.-5:00 P.M.     

 

 

 

Print | Sitemap
© Scotts Gunsmithing